Filter Assembly Picture
Filter Assembly More Information Link

 

Part # 100-60 - Oil Filter Assembly with
60 micron filter element- PRICE $495.00

 

Part # 100-115 - Oil Filter Assembly with
115 micron filter element- PRICE $495.00

 

Assembly Includes the following: 2 - #12 O-Ring Boss Plugs but does not come with Inlet or Outlet Hose Fittings, comes with Directions and choice of either 60 or 115 Micron Filter Element

 

Click Below to Enlarge Direction Pages

Part # 100-60 & 115 Filter Direction Page Link

Clear View Filtration's New Fluid
and Oil Filter Assembly
(patent pending)

 

Clear View Filtration's new patent pending fluid filter assembly allows the user to visually see the fluid pumping through the filter, which helps in determining the condition of the fluid.


When fluid is not being pumped through the filter, the filter assembly can be quickly drained using compressed air and an air chuck for filling tires. An air bottle or a CO2 cartiage bicycle tire filler works great, just apply a small shot of air to the air fitting on the side of the inlet opening. The fluid will empty out of the filter assembly in seconds exposing the filter element. This allows the user to visually see any contaminants and particles that were filtered out of the fluid system. This helps to determine if the contaminants and particles are from normal use or from bearings or components excessively wearing in machinery or the engine supplying the filter assembly.


This filter assembly is designed for racing, the filter element can be visually checked in just a few seconds. This makes it possible for a circle track racer to check the filter element for excessively wearing engine parts, even during a pit stop in the middle of a race. Now drag racers can easily check the filter element between rounds. The old style filters made this almost impossible, especially in the later rounds. There is not enough time to take the old style oil filter apart, and clean up the mess, and put the filter back together. The racer usually has to take the filter apart when it is very hot. No madder what kind of racing you are doing, Clear View Filtration's new Oil Filter Assembly will give the user the ability to keep track of their engine, by being able to visually check the filter in seconds without draining or leaking any oil, unbolting or loosening any fasteners or fittings and you don't loose any fluid out of the fluid system.


The Filter Assembly is machined out of 6061 T6 billet aluminum and Clear Anodized for Protection and Durability. The Sight Window is made out of high-grade plastic that is chemical, heat, scratch, and shatter resistant. The Filter Element is made out of stainless steel mesh that can easily be cleaned and reused.


Twelve Radial Groove Openings operate like twelve individual filters enclosed into one Filter Assembly. This allows more fluid to pass through the Filter Assembly without restriction, even as the Filter Element is plugging up with dirt and contaminates. If one of the twelve grooves were to plug completely the fluid would flow through another groove that was not plugged completely.


The Filter Assembly also is equipped with a Pressure Relief Valve. If the filter pressure rises due to the Filter Element plugging up, the Relief Valve will open allowing fluid to pump through the Filter Assembly even if the Filter Element were to plug up completely. This will help prevent motor failure caused by the filter being plugged.


The filter assembly part #100 is designed for fluid systems with a max working pressure of 125 PSI at 180 degrees temperature. If filtering higher pressures or temperatures, contact us and let us know your application. We can also design and supply Clear View Filtration's filters assemblies for custom applications.

 

The physical dimentions of the filter assembly are: 6 3/4" Wide x
7 3/4" Long x 3 1/4" Thick and Weight's 5 1/2 pounds.

 

 

 

Clear View Filtration's 6" Screw-On See Through Filter Assembly

are designed for applications where a large Fram #HP-6 / HP-6A,

K&N #HP-5001, or a Wix #51222R Screw-on Filter is used.

6" Screw On Filter Assembly Top View

Part # 125-115 - 6" Hi-Flow Screw On Oil Filter Assembly
with 115 micron filter element- PRICE $495.00


Filter Assembly Includes: 2 - #12 O-Ring Boss Plugs, 115 micron filter

element, and Directions, but does not come with Inlet or Outlet

Hose Fittings or a Disposable Filter (Filter uses a

Fram #HP-6 / HP-6A, K&N #HP-5001, or Wix #51222R)

6" Screw On Filter Assembly Side Virew

This new filter assembly was designed for tractor pulling and other motor sports ran on dirt. It also works for the user who wants to filter microscopic and dust particles out of a fluid system which flows high volumes of fluid.

 

Just like the other Screw-On Filter Assemblies the fluid first flows through the See Through Filter in which the filter element traps all the larger particles which can be viewed and inspected while the microscopic particles flow into the disposable filter and are filtered out of the fluid. The clean filtered oil then flows out of the filter assembly through the outlet opening. This dual stage filter will extend the life and flow of the disposable filter and still allow visual inspection of the contaminants and particles filtered out of the oil system.

 

The Dimenstions of this 6" Filter Assembly (without Screw-On Filter) :
6 3/4" Wide x 7 3/4" Long x 3 1/4" Thick & Weighs 5.5 lbs.

 

 

4" Screw On Filter Assembly Bottom View

 

 

 

 

Pictured Left is side view of
6" Screw-On Filter Assembly!

Click Below to Watch a Video with Information
and a Demonstration of the Filter Assembly

 

 

Click Here To Enlarge Direction Page Link
Part # 125-115 Screw On Filter Direction Page Link

 

Clear View Filtration's NEW 4" See Through Filter Assemblies

are designed for applications where limited space and being light weight are ideal!

3 different styles of 4" filter asemblies for all types of applications

4" Screw On Filter Assembly Top View

 

Part # 400-115 - 4" Screw On Oil Filter Assembly with 115 micron filter element- PRICE $395.00


Assembly Includes: 1 - #12 O-Ring Boss Plug and Directions,
but does not come with Inlet or Outlet Hose Fittings or a Disposable Filter
4" Screw On Filter Assembly Side Virew

The 4" See Through Filter Adapter was designed to accept a stock style screw on filter for applications were microscopic particles need to be filtered out.


This filter assembly was designed for motor sports ran on dirt such as tractor pulling, dirt track cars, and other applications where the user wants to filter microscopic and dust particles out of the oil system. This filter assembly is also the best choice for marine and street use. The oil first flows through the See Through Filter which the filter element traps all the larger particles which can be viewed and inspected while the microscopic particles then flow into the disposable filter and are filtered out of the oil. The clean filtered oil then flows back into the engine. This dual stage filter will extend life and flow of the disposable filter and still allow visual inspection of the particles and contaminants filtered out of the oil system.

 

The physical dimentions of the 4" filter assembly with out the screw on filter are: 5" Wide x 6" Long x 3" Thick and Weight's 3.2 pounds

 

Click Below to Enlarge Direction Pages
Part # 400-115 Screw On Filter Direction Page Link Part # 400-115 Screw On Filter Direction Page Link

4" Hi-Flow See Through Filter Assembly
4" High Flow Filter Assembly

This Hi-Flow 4" See Through Filter Assembly filters fluids being pumped through a .625" or 5/8" inside diameter hose or smaller.
Inlet and Outlet openings threaded for #12 fittings

 

Part # 410-60 - 4" Hi-Flow Oil Filter Assembly with 60 micron filter element- PRICE $385.00

 

Part # 410-115 - 4" Hi-Flow Oil Filter Assembly with 115 micron filter element- PRICE $385.00

 

Assembly Includes: 1 - #12 O-Ring Boss Plug and Directions,
but does not come with Inlet or Outlet Hose Fittings

 

The physical dimentions of the 4" filter assembly are:

5" Wide x 6" Long x 3" Thick and Weight's 3 pounds

Billet Connection also makes a 4" See Through Filter Assembly for Fuel / Transmission application

 

This Filer is the same as the 4" Hi-Flow Filter Assembly pictured to the left. The only difference is the Filter Base is 1/2" thinner and the Inlet and Outlet fitting holes are threaded for a #8 fitting. Designed for fluids being pumped through a .375" or 3/8" inside diameter hose or smaller.

 

Part # 420-28 - 4" Transmission Oil Filter Assembly
with 28 micron filter element- PRICE $375.00

 

Part # 420-60 - 4" Transmission Oil Filter Assembly
with 60 micron filter element- PRICE $375.00

 

Part # 420-115 - 4" Transmission Oil Filter Assembly
with 115 micron filter element- PRICE $375.00

 

Assembly Includes: 1 - #8 O-Ring Boss Plug and Directions,
but does not come with Inlet or Outlet Hose Fittings

The physical dimentions of the 4" filter assembly filter are:

5" Wide x 6" Long x 2 1/2" Thick and Weight's 2.8 pounds

 

Click Below to Enlarge Direction Pages
Part # 410 & 420 Filters Direction Page LinkPart # 410 & 420 Filters Direction Page Link
 

REPLACEMENT PARTS FOR 6" FILTER ASSEMBLIES:

WE RECOMMEND THAT YOU ALSO PURCHASE THESE REPLACMENT PARTS FOR YOUR FILTER ASSEMBLY

 

FILTER ELEMENTS
Part # 110-60 - Replacement 6 inch 60 Micron Filter Element- PRICE $45.00

The 60 Micron Filter Element works good for engine oils up to 50 weight.


Part # 115-115 - Replacement 6 inch 115 Micron Filter Element- PRICE $45.00

The 115 Micron Filter Element used with screw on filters or 60 weight or heavier engine oils.

 

REPLACEMENT POLY CARBONATE SIGHT WINDOWS

Filter Assembly Window Retainers are engraved with a Part number that can been seen through the Sight Window. The Part number is located by the By-Pass Nut in the center of the Window Retainer.

Part # 104-475 - Replacement 6 inch 0.475" Thick Window- PRICE $25.00
Part # 105-480 - Replacement 6 inch 0.480" Thick Window- PRICE $25.00

Part # 106-485 - Replacement 6 inch 0.485" Thick Window- PRICE $25.00

The transparent sight windows are resistant to chemicals, solvents, petroleum oils, and is also
vibration and impact resistant. 

 

O-RING KIT

Part # 120 - Replacement 6 inch Filter Assembly O-Ring Kit- PRICE $9.95

Includes; Sight Window Viton O-Ring, Window Retainer Viton O-Ring, & Filter Housing Bore O-Ring.

 

REPLACEMENT PARTS FOR 4" FILTER ASSEMBLIES:

WE RECOMMEND THAT YOU ALSO PURCHASE THESE REPLACMENT PARTS FOR YOUR FILTER ASSEMBLY

 

FILTER ELEMENTS

Part # 430-28 - Replacement 4 inch 28 Micron Filter Element- PRICE $35.00

The 28 Micron Filter Element works good when used for any fuels or transmission fluid.


Part # 435-60 - Replacement 4 inch 60 Micron Filter Element- PRICE $35.00

The 60 Micron Filter Element works good for engine oils up to 50 weight.

 

Part # 440-115 - Replacement 4 inch 115 Micron Filter Element- PRICE $35.00

The 115 Micron Filter Element used with screw on filters or 60 weight or heavier engine oils.

 

REPLACEMENT POLY CARBONATE SIGHT WINDOWS

Filter Assembly Window Retainers are engraved with a Part number that can been seen through the Sight Window. The Part number is located by the By-Pass Nut in the center of the Window Retainer.

Part # 411-475 - Replacement 4 inch 0.475" Thick Window- PRICE $20.00
Part # 412-480 - Replacement 4 inch 0.480" Thick Window- PRICE $20.00

Part # 413-485 - Replacement 4 inch 0.485" Thick Window- PRICE $20.00

The transparent sight windows are resistant to chemicals, solvents, petroleum oils, and is also
vibration and impact resistant. 

 

O-RING KIT
Part # 425 - Replacement 4 inch Filter Assembly O-Ring Kit- PRICE $8.95

Includes; Sight Window Viton O-Ring, Window Retainer Viton O-Ring, & Filter Housing Bore O-Ring.

Blue Aluminum Fitting
ALUMINUM
Silver Steel Fitting
STEEL

Part # 160 - #12 O-Ring Boss to #12 JIC Male Fitting
with 1 1/4" Nut; Billet Aluminum - PRICE $9.95 each

Part # 161 - #12 O-Ring Boss to #12 JIC Male Fitting
with 1 1/4" Nut; Steel - PRICE $4.95 each

The #12 straight thread with an o-ring fitting are a common size. Most fitting dealers carry steel fittings that come with #12 straight thread with an o-ring on one end and lots of different options on the other end. The preferred fittings are #12 straight thread with o-ring (*sometimes called #12 male o-ring boss fitting*) on one end and a #12 JIC male on the other end. This accepts #12 JIC female fittings which come in all different configurations. A #12 JIC female 90 degree to #12 hose is the fittings and hose to use for most applications it runs the oil lines along the pan rail towards the front of the motor. This also helps on racing applications where an engine diaper is used.

Click Below to Watch a Video with a
Demonstration of the Filter Assembly


Video is the same as above just the Demonstration!
 

6" Hi-Flow Filter Mounting Brackets

 

The bracket kits below mount the 6" Filter Assembly for various applications. If you dont see a bracket kit that will work for your application, we can make custom mounting bracket to fit your needs. The brackets are made out of 6061 billet aluminum. The kits come with fasteners to bolt the brackets to the filter assembly and fasteners to bolt the brackets to a 1/4" thick or thinner mounting surface.

Part # 175 STRAIGHT - PRICE $ 24.99

These bracket will Mount to both the 6" Hi-Flow and the6" Screw-On Filter assemblies. This bracket brings the mounting holes out to the side of the filter assembly. It can be mounted to a flat surface with the 3/8" mounting holes and a center to center hole spacing of 2.000".
Side Bracket Installed on  Screw-On Filter (PNG)
 
If there are already mounting holes where a different
brand of remote filter was mounted. Make sure to check all the different Mounting Flanges below to be able to adapt to differerent hole spacings.

BottomSide Bracket Installed on HiFlow Filter (PNG)BottomSide Bracket Installed on ScrewOn Filter (PNG)

Click below for More Information & Directions
Part No 180 the 6in Mounting Bracket Direction Page LINK

Part # 184 UP - PRICE $ 54.99

This bracket kit will Mount the 6" Hi-Flow Filters to applications that need the filter assembly to be raised higher than the mounting location.
 

 

Part No 184 the 6in UP Mounting Bracket


Click below for More Information & Directions
Part No. 184 - Directions Picture Link

Part #188 DOWN or UP
PRICE $ 34.99

This bracket kit will Mount to both the 6" Hi-Flow and the 6" Screw-On Filter assemblies. This bracket kit will Mount the 6" Filters to applications that need to be lowered. This bracket can also be turned over which will raise the filter above the mounting location.
 

Part No 188 the 6in DOWN Mounting Bracket


Click below for More Information & Directions
Part No. 188 - Directions Picture Link

Part # 175 Mounting Flanges

 

We offer Different Mounting Flanges that bolt to Part #175 Straight Bracket. The Mounting Flange Hole Spacing adapts the Part #175 Straight Bracket to Mounting Holes for different brands of remote filter assemblies to accomidate mounting taps and mounting holes already there. The Part #175 Straight Bracket has 2.00" center to center Mounting Holes. The flanges we offer adpat Part #175 Straight Bracket to 2.375", 2.600", or 3.000" hole center to center spacing. We also offer a 3 bolt flange that mounts to the end of the Part #175 Straight Bracket. Call us and tell us what brand of remote filter is being used and we can tell you what flange will adapt to that application. We can also mae custom mounting flanges or brackets to fit any application.

PART #176 - 3 BOLT MOUNTING 
FLANGE - PRICE $ 14.99
3 Hole Bracket for P# 175Part # 176 Direction Page LINK
Click for Directions

PART #177 - 2.375" MOUNTING HOLES
FLANGE - PRICE $ 7.99

PART #178- 2.600" MOUNTING HOLES FLANGE - PRICE $ 7.99
2.600in Holes TopSide Bracket Adapter

PART #179- 3.000" MOUNTING HOLES
FLANGE - PRICE $ 7.99
3.000in Holes TopSide Bracket Adapter

 

4" Hi-Flow Filter Mounting Brackets

 

These kits will mount the 4" Filter Assemblies to either a flat surface at 90 degrees, or to a flat surface on an angle. Call for bracket kits that will mount the Filter to 1 1/4", 1 3/8", 1 1/2", or 1 5/8" round tubing and be able to be angled so the filter top is flat. Call if any questions! If you dont see a bracket kit that will work for your application, we can make custom mounting bracket to fit your needs. The brackets are made out of 6061 billet aluminum. The kits come with fasteners to bolt the brackets to the filter assembly.

Part # 470 - PRICE $ 9.99

4in Filter Straight Bracket Kit P# 470

Part # 475 - PRICE $ 14.99

 

4in Filter Angle Bracket Kit P# 475

Click Below for more Information and

the Directions Page for the 4" Mounting Brackets Part #470 & #475
Part No.'s 470 & 475 - Directions Page Picture Link

 

BLOCK ADAPTER KITS

All Billet Connection's Block Adapters are machined out of 6061 Billet Aluminum for strength and are Clear Anodized for better protection and easier maintenance. The Block Adapters all have high flow designs for high pressure and high volume engine oil systems for today's Performance and all out Race Engines.

 

Billet Connection can build Block Adapters that will screw on in place of any disposable fluid filter that adapts to threaded inlet and outlet openings. We can build and design adapters for different application, making it possible for the inlet and outlet openings in a fluid system to adapt to a threaded hose fitting. This will allow easy installation of theSee Through Filter Assemblies to any fluid system.

Click To Enlage Direction Page Link
Block Adapter Directions Page Link